You can also use CA glue that the fabricators use..Its basically a super glue..Its crystal clear and flows like water. Perfect for hairline cracks

On Mon, Mar 14, 2011 at 3:55 PM, John Freitag <jfreitag@thestoneandtileschool.com> wrote:

Stuart,

 

I would recommend cleaning the cracks using an alkaline based cleaner using professional dental picks, then clean the crack  with Acetone then fill the hole with a flowing bases polyester fill . in this case a clear color might be your best bet.

 

 

John E. Freitag

President/Director

The Stone and Tile School

Office 407-567-7652

Cell 407-615-0134

jfreitag@thestoneandtileschool.com

 

schoollogo

 

www.thestoneandtileschool.com

 

 

 

From: Stuart Young [mailto:santafefc@sbcglobal.net]
Sent: Monday, March 14, 2011 3:46 PM
To: Restoration and Maintenance
Subject: [sccpartners] hairline cracks

 

Gentlemen,

 

On a regular basis I am asked to repair hairline cracks (stress cracks) what ever you want to call them.  I haven't a clue as to how to repair them, or even make them invisible.  I know that what you see in the crack is usually dirt.  But I just don't know what to do. This is such a recurring problem that surely, there must be some remedy.  I need some help.

 

Stuart Young

Santa Fer Floor Care

----- Original Message -----

Sent: Monday, March 14, 2011 10:18 AM

Subject: RE: [sccpartners] Swirl Marks

 

Roger ,

 

Why not use honing powders. By the time you figure the cost of the pads the powder will probably be more cost effective and will guarantee a consistent finish. where as the pads as they wear could give you an inconsistent finish.

 

 

 

John E. Freitag

President/Director

The Stone and Tile School

Office 407-567-7652

Cell 407-615-0134

jfreitag@thestoneandtileschool.com

 

schoollogo

 

www.thestoneandtileschool.com

 

  

 

From: Roger Konarski [mailto:qm144@yahoo.com]
Sent: Saturday, March 12, 2011 6:21 PM
To: Restoration and Maintenance
Subject: RE: [sccpartners] Swirl Marks

 

I have used the pads on two prior jobs and did not have the same problem. Anyway I think we got the issue resolved, I tried to take a short cut to remove the factory swirls, which is use only pads. Looks like we need to cut the floor 1st with diamonds and then use pads. So far the initial test looks promising.

I don’t want to use honing powders, the job is 8500 sq.ft.

 

 

 

 

--- On Sat, 3/12/11, Darek Nicinski <mail@rocklandstonerestoration.com> wrote:


From: Darek Nicinski <mail@rocklandstonerestoration.com>
Subject: RE: [sccpartners] Swirl Marks
To: "Restoration and Maintenance" <sccpartners@stoneandtilepros.com>
Date: Saturday, March 12, 2011, 4:21 PM

That's what they do at least the one i tray and i will suggest you use a honing powder instead

On Sat, Mar 12, 2011 at 4:57 PM, Roger Konarski <qm144@yahoo.com> wrote:

I’m using velocity pads to clean up a newly installed honed marble floor.  We are having problems with the pads leaving swirl marks. What are we doing wrong that we are getting swirl marks?





--
Regards,

Darek Nicinski
Rockland Stone Restoration
845-323-7333
www.rocklandstonerestoration.com



Powered by http://DiscussThis.com
Visit list archives, subscribe, unsubscribe or change your subscription preferences
Start a new conversation (thread)


Powered by http://DiscussThis.com
Visit list archives, subscribe, unsubscribe or change your subscription preferences
Start a new conversation (thread)


Powered by http://DiscussThis.com
Visit list archives, subscribe, unsubscribe or change your subscription preferences
Start a new conversation (thread)




--
Frederick M. Hueston PhD
www.stoneforensics.com
www.stoneandtilepros.com
Recommended stone care products  http://www.stonecarecentral.com

Many of my informational articles can be found at www.stoneandtilepros.com

Listen to my radio show at www.blogtalkradio.com/drfred
The Ultimate Stain Remover  www.GoDrFred.com

Cell 321-514-6845