You may also try a simple way to help the customer without getting to involved. 
http://www.theheavyweight.com


Sincerely,
Dustin Fox




On Sat, Apr 9, 2011 at 12:47 PM, <flooramor@aim.com> wrote:
Thanks for the feedback guys. Had the same feeling as you three but wanted to throw it out there just in case there was something new I was not aware of yet.

J


Sent from my BlackBerry® smartphone with Nextel Direct Connect


From: "John Freitag" <jfreitag@thestoneandtileschool.com>
Date: Sat, 9 Apr 2011 14:17:12 -0400
To: Restoration and Maintenance<sccpartners@stoneandtilepros.com>
ReplyTo: "Restoration and Maintenance" <sccpartners@stoneandtilepros.com>
Subject: RE: [sccpartners] Grinding saltillo

I AGREE !!!!!!!  IF YOU GRIND THIS FLOOR PLAN ON REPLACING IT. RUN DON’T , DON’T JUST WALK AWAY !!! HOPEFULLY  FRED  AND I MADE OURSELVES CLEAR ON THIS

 

 

John E. Freitag

President/Director

The Stone and Tile School

Office 407-567-7652

Cell 407-615-0134

jfreitag@thestoneandtileschool.com

 

schoollogo

 

www.thestoneandtileschool.com

 

 

 

From: Fred Hueston [mailto:fhueston@gmail.com]
Sent: Saturday, April 09, 2011 10:03 AM
To: Restoration and Maintenance
Subject: RE: [sccpartners] Grinding saltillo

 

NO NO NO  DO NOT Grind it..you will ruin it..There is not a lot you can do other than to maybe put a coating on it that is non slippery.

On Sat, Apr 9, 2011 at 4:28 AM, stuart rosen <mail@stoneshine.com> wrote:

I dont think grinding saltillo would work too well, Not to mention restaurant guys always seem to look for cheapest way. Why not clean and strip if needed then look into the coatings at richard james that you could make slip resistant.

 

On Fri, Apr 8, 2011 at 8:11 PM, <flooramor@aim.com> wrote:

A restaurant owner with a saltillo floor that is constantly slippery asked me if there was a way to clean it and flatten it in order to make it easier for them to keep clean.

I know that saltillo is mud, really, with a glaze but don't know if grinding it flat would be feasible and afterwards apply the coatings needed to protect it along with some abrasive or coarse shark grit type material to give the floor some traction.

Any thoughts or suggestions? Please share any feedback.

Thanks,

J

Sent from my BlackBerry® smartphone with Nextel Direct Connect
--
Powered by http://DiscussThis.com
Visit list archives, subscribe, unsubscribe or change your subscription preferences:
http://www.discussthis.com/members/sccpartners@stoneandtilepros.com
Start a new conversation (thread): sccpartners@stoneandtilepros.com



--

Regards,
Stu Rosen
201-446-1200
www.mbstonecare.com  " WORLD CLASS STONECARE PRODUCTS "

 

 





--
Frederick M. Hueston PhD
www.stoneforensics.com
www.stoneandtilepros.com
Recommended stone care products  http://www.stonecarecentral.com

Many of my informational articles can be found at www.stoneandtilepros.com


Listen to my radio show at www.blogtalkradio.com/drfred

The Ultimate Stain Remover  www.GoDrFred.com

 


Powered by http://DiscussThis.com
Visit list archives, subscribe, unsubscribe or change your subscription preferences
Start a new conversation (thread)


Powered by http://DiscussThis.com
Visit list archives, subscribe, unsubscribe or change your subscription preferences
Start a new conversation (thread)


Powered by http://DiscussThis.com
Visit list archives, subscribe, unsubscribe or change your subscription preferences
Start a new conversation (thread)

=