Sent: Tuesday, September 13, 2011 5:10 PM
Subject: RE: [sccpartners] Chip patching
Problem is that I have the side and arris to do so I need something knife grade. AM told that even epoxy, if it is clear, can still yellow. Now I am leaning more towards a UV cure epoxy acrylate. I think the acrylates will not yellow (as most acrylics don’t) so I will just need to apply, wrap with clear tape and uv cure, pull tape. This is used for surfboard repair and it does not yellow, perfectly clear. Called Solarez. Goes off in 5 mins in the sun. Or I might use a thick CA, with an accelerator.
From: john jackson [mailto:kcstoneguy@yahoo.com]
Sent: Wednesday, September 14, 2011 12:18 PM
To: Restoration and Maintenance
Subject: RE: [sccpartners] Chip patching
i think i used either akemi or bellazoni brands. btw
From: john jackson <kcstoneguy@yahoo.com>
To: Restoration and Maintenance <sccpartners@stoneandtilepros.com>
Sent: Tuesday, September 13, 2011 9:13 PM
Subject: RE: [sccpartners] Chip patching
if its exterior you should use an exterior grade epoxy so the uv lighting will not affect it. (thats what I was told last year)..I did a granite cladding repair that had been damaged by skateboarder last year...it has held up well..pure epoxy will work better than polyester epoxy..btw, the trick i came up was put tape on the outside, then filled the hole with epoxy on a razor blade..when it hardened, i pulled the tape...it left a nice crisp fill, then i just rounded it off with a razor blade...fast and pretty simple repair..
From: Mike Marsoun <nulifesc@bigpond.com>
To: Restoration and Maintenance <sccpartners@stoneandtilepros.com>
Sent: Tuesday, September 13, 2011 7:19 PM
Subject: RE: [sccpartners] Chip patching
Thanks. Looking for something knife grads so I can blade it in.
From: Fred Hueston [mailto:fhueston@gmail.com]
Sent: Wednesday, September 14, 2011 9:43 AM
To: Restoration and Maintenance
Subject: RE: [sccpartners] Chip patching
Tenax, Touchstone by bonstone
Tenax makes a water clear flowing 2 part epoxy.
Fred can you recommend a brand?
From: Fred Hueston [mailto:fhueston@gmail.com]
Sent: Tuesday, September 13, 2011 10:05 PM
To: Restoration and Maintenance
Subject: RE: [sccpartners] Chip patching
thats what I would use, a clear epoxy.
I will be doing this job where the pictured greek marble will be used. It is very dense. There are chips on a lot of the edges and corners. They want it all removed by grinding but I told them I would need to patch the bigger chips, not going to be committed to grind so deep... It is exterior, so I need an epoxy rather than a polyester. Any suggestions for the glue? The chips are so small I was thinking about using the epoxy clear.
Sent via BlackBerry® from Telstra
--
Powered by http://DiscussThis.com
Visit list archives, subscribe, unsubscribe or change your subscription preferences:
http://www.discussthis.com/members/sccpartners@stoneandtilepros.com
Start a new conversation (thread): sccpartners@stoneandtilepros.com
No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 9.0.914 / Virus Database: 271.1.1/3877 - Release Date: 09/13/11 04:35:00
WORLD CLASS STONECARE PRODUCTS
No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 9.0.914 / Virus Database: 271.1.1/3877 - Release Date: 09/14/11 04:35:00
Powered by http://DiscussThis.com
Visit list archives, subscribe, unsubscribe or change your subscription preferences
Start a new conversation (thread)
No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 9.0.914 / Virus Database: 271.1.1/3877 - Release Date: 09/14/11 04:35:00
Powered by http://DiscussThis.com
Visit list archives, subscribe, unsubscribe or change your subscription preferences
Start a new conversation (thread)
No virus found in this message.
Checked by AVG - www.avg.com
Version: 10.0.1392 / Virus Database: 1520/3894 - Release Date: 09/13/11