I would start with 20% iron out to DE powder. Just mix till its the consistency of yougart...Yes it will etch.

On Mon, Jul 2, 2012 at 1:53 AM, Stuart Young <santafefc@sbcglobal.net> wrote:
Thank you for your responses. I'm curious about using an Iron Out poultice - what sort of ratios are you using for this purpose (how much Iron Out to water).  The directions on the back of the bottle for exterior uses says 1 cup Iron Out to 1 gallon of water.  Does that sound about right?  We tried a stronger Iron Out poultice on travertine and it seemed to etch the stone.
 
After that I suppose you use as much liquid as necessary to make a nice paste with DE powder?
 
Thank  you,
Stuart
----- Original Message -----
Sent: Sunday, July 01, 2012 9:00 AM
Subject: RE: [sccpartners] Thassos marble restoration

I think you are right about the water-if these bathrooms get a lot of use then it could be possible the stone gets a good amount of splashing from the hand dryers. Over time there could have been some oxidation. I have seen this with thassos before in shower stalls.
Thassos can be very porous and I think fred will agree has an iron content .If the basic stuff doesnt work try an iron -out poultice.
Hone the areas first then apply the poultice. You can melt the iron out in water and then use a powder or DE to apply it. You can also make a paste withwater and iron out which seems to quite strong ans works pretty well. It also dries out alot faster that way.

On Thu, Jun 28, 2012 at 1:27 PM, Fred Hueston <fhueston@gmail.com> wrote:
From the photos it looks like oils or some type of chemical..I would hone the floor and than scrub it with a good alkaline and than polish


On Thu, Jun 28, 2012 at 5:57 AM, Stuart Young <santafefc@sbcglobal.net> wrote:
Good afternoon,
 
We will be working on some thassos marble tiles in 2 bathrooms in a hair salon. These tiles form a small band around the rooms on the wall and the majority of the tiles look like new (see photo).  Under the hand dryers, however, there is some darkness, particularly around the edges (photo looks darker than actual tiles - they are mostly white).
 
We are not sure of the cause of the discoloration - it could be from water from those drying their hands - who knows what chemicals or products are being used in a salon.  Is it possible that the hand dryers (which are directly above these stones) could discolor the tiles from heat?
 
Our plan of attack is to hone and polish these tiles.  Anyone have any other suggestions?  What would be the best way to prevent this from happening in the future?
 
Stuart Young
Santa Fe Floor Care
Austin TX

Powered by http://DiscussThis.com
Visit list archives, subscribe, unsubscribe or change your subscription preferences
Start a new conversation (thread)




--
Frederick M. Hueston PhD
www.stoneforensics.com
www.stoneandtilepros.com

Recommended stone care products  http://www.stonecarecentral.com

Many of my articles can be found at www.stoneandtilepros.com
Listen to my radio show   www.blogtalkradio.com/drfred
office             321 514 6845      
See my specialty products at  www.godrfred.com



--
www.mbstone.com
www.stoneshine.com
"EVERYTHING MATTERS "
 


Powered by http://DiscussThis.com
Visit list archives, subscribe, unsubscribe or change your subscription preferences
Start a new conversation (thread)


Powered by http://DiscussThis.com
Visit list archives, subscribe, unsubscribe or change your subscription preferences
Start a new conversation (thread)




--
Frederick M. Hueston PhD
www.stoneforensics.com
www.stoneandtilepros.com
www.safeandcompliant.net

Recommended stone care products  http://www.stonecarecentral.com

Many of my articles can be found at www.stoneandtilepros.com
Listen to my radio show   www.blogtalkradio.com/drfred
office             321 514 6845      
See my specialty products at  www.godrfred.com