Since concrete is pretty much all I do anymore, most of them residential, here are some thoughts:

As someone mentioned, do a mock up. The biggest issue with polished concrete is when expectations of the homeowner are not met. 

If your floor is flat and smooth(use a straight edge to see), edges included, than you should be fine. As everyone knows the most difficult part of polishing concrete is the edges. If edges are not troweled smooth like the rest of the floor, you may not get them to ever match. Exposing large aggregate may be the answer but sometimes this will not work either.

Most basement floors are not finished very well on the edges, therefore we find it is a rarity to be able to do a cream polish. Most specs call for Ff numbers of at least 40. My general rule is that if I find a 1/4 defect in 10'(Ff 25), it should not be cream polished, but ground with at least two or three metal bonds. I have never been able to cream polish a basement that has been hand troweled. Look for basements that a power trowel has been used. It means the floor will be in better condition.

If you find you are blowing through your diamonds, stop and densify. Those of us you do this regularly use soft or hard bonded diamonds to match the hardness of the concrete, so our diamonds last longer.

Hope this helps. Have fun!

Jason Francis

econcrete

On Thu, Jun 6, 2013 at 10:40 PM, John Freitag <jfreitag@thestoneandtileschool.com> wrote:

Kevin ,

If you want basic concrete polishing training only I can train you on the
basics.  Call me before you pass on this job

John E Freitag
Director
The Stone & Tile School
Office 407-567-7652
Cell 407-615-0134
jfreitag@thestoneandtileschool.com



www.thestoneandtileschool.com



-----Original Message-----

From: K. Hudson [mailto:klhudson16@comcast.net]
Sent: Thursday, June 06, 2013 9:25 PM
To: Stone and Tile PROS Technical Support

Subject: RE: [sccpartners] Concrete polishing.

Thank you all for your great advise! However,since I am not currently
professionally trained in polishing concrete I am considering passing this
job on! With that in mind who do you all recommend I contact for training on
concrete polishing? Thanks!

Kevin
N-Motion Stone and Tile

Sent from my iPhone


On Jun 6, 2013, at 8:51 PM, "John Freitag"
<jfreitag@thestoneandtileschool.com> wrote:

> Kevin
> If the concrete had been finished properly the honing and polishing is
easy.
> Purchase some concrete diamonds . if the concrete is a good pour and
> smooth good cream finish then you can probably start with a 100 grit
> or 220 grit diamond, then after the200 grit diamond add you densfilier
> I prefer to allow the densflier to penetrate into the concrete for at
> least 1 hour. vac up any excess materials.
> Then I prefer to use a finish mop and mop on a very thin thin coat of
> the densflier and allow to set over night. Then come back the next day
> and hone
> 400 , 800, 1500 , 3000 and you should have a great polish.
>
>
> John E Freitag
> Director
> The Stone & Tile School
> Office 407-567-7652
> Cell 407-615-0134
> jfreitag@thestoneandtileschool.com
>
>
>
> www.thestoneandtileschool.com
>
>
>
>
> -----Original Message-----
> From: N-Motion Stone and Tile Care
> [mailto:klhudson@atlantastoneandtilecare.com]
> Sent: Sunday, June 02, 2013 11:13 PM
> To: Stone and Tile PROS Technical Support
> Subject: [sccpartners] Concrete polishing.
>
> Partners,
> I have been asked to polish 450 sq ft of concrete in a customer basement.
> The concrete has been down since October of 2012. I am looking for
> advise from those of you who have expertise in this area. Any advise
> would be greatly appreciated. Thanks!
>
> Kevin Hudson
> N-Motion Stone and Tile
>
> Sent from my iPhone
>
>
> --
> Powered by http://DiscussThis.com
> Visit list archives, subscribe, unsubscribe or change your
> subscription
> preferences:
> http://www.discussthis.com/members/sccpartners@stoneandtilepros.com
> Start a new conversation (thread): sccpartners@stoneandtilepros.com
>
>
>
>
>
>
>
> --
> Powered by http://DiscussThis.com
> Visit list archives, subscribe, unsubscribe or change your subscription
preferences:
> http://www.discussthis.com/members/sccpartners@stoneandtilepros.com
> Start a new conversation (thread): sccpartners@stoneandtilepros.com
>
>
>

--
Powered by http://DiscussThis.com
Visit list archives, subscribe, unsubscribe or change your subscription
preferences:
http://www.discussthis.com/members/sccpartners@stoneandtilepros.com
Start a new conversation (thread): sccpartners@stoneandtilepros.com







--
Powered by http://DiscussThis.com
Visit list archives, subscribe, unsubscribe or change your subscription preferences:
http://www.discussthis.com/members/sccpartners@stoneandtilepros.com
Start a new conversation (thread): sccpartners@stoneandtilepros.com

--

 

Marble Glow
Jason Francis
Sales / Lead Stone Pro
www.marbleglow.com
333 Norton Road
Red Hook, NY 12571
718-514-7343 NYC 

845-208-8289 Upstate 

 

---

Powered by http://DiscussThis.com
Visit list archives, subscribe, unsubscribe or change your subscription preferences

Start a new conversation (thread)