From my use of crystallization and jobs I have seen in most cases there too much crystallization used. A fine mist is all you need, especially if you have already polished the stone with a polishing powder. If you using fine mist you can get 1000 or more sq.ft. before the pad become too wet. On some floors ( greens) the more build up you get in the pad the better it works ,however at the end you need to use a dry pad and buff off.

John E Freitag

Director

The Stone & Tile School

Office 407-567-7652

Cell 407-615-0134

jfreitag@thestoneandtileschool.com

<image001.jpg>

www.thestoneandtileschool.com

From: list-manager@stoneandtilepros.simplelists.com [mailto:list-manager@stoneandtilepros.simplelists.com] On Behalf Of Perfect Marble 2
Sent: Wednesday, May 21, 2014 11:42 AM
To: sccpartners@stoneandtilepros.simplelists.com
Subject: Re: Swirl Marks

Swirl marks may be to using to much crystallizer and steel wool pad is loaded with product. Apply small amount and flip pad every 600 ft

Sent by iPhone

Dayron Padilla

Perfect Marble

On May 21, 2014, at 11:41 AM, "John Freitag" <jfreitag@thestoneandtileschool.com> wrote:

I disagree with 000 or 0000 steel wool. This steel wool will generate too much heat and you will run a high risk to dulling the floor or what known as burning the surface by generating too much heat.

The #1 steel wool is the best grade to use and the only grade I use and the only grade we use when training.

John E Freitag
Director
The Stone & Tile School
Office 407-567-7652
Cell 407-615-0134
jfreitag@thestoneandtileschool.com

<image001.jpg>

www.thestoneandtileschool.com

From: list-manager@stoneandtilepros.simplelists.com [mailto:list-manager@stoneandtilepros.simplelists.com] On Behalf Of Georgia
Sent: Wednesday, May 21, 2014 11:20 AM
To: sccpartners@stoneandtilepros.simplelists.com
Subject: Re: Swirl Marks

Roger. That steel wool is too corse. 000 or 0000 is best. The swirl marks will need to be honed out.
On May 21, 2014 9:18 AM, "Roger Konarski (via sccpartners list)" <nobody@simplelists.com> wrote:
This email was sent from yahoo.com which does not allow forwarding of emails via email lists. Therefore the sender's email address (qm144@yahoo.com) has been replaced with a dummy one.

My techs did a commercial job with black marble. The final strep way to crystalize the floor. I just got a call back with issues of swirl marks. They use 0 steel wool. We very rarely crystalize , thus have very little experience in that area.
What did we do wrong and needs to de done to correct the problem?

Thanks,

Roger
 
Visit list archives, subscribe, unsubscribe or change your subscription 
preferences:
http://stoneandtilepros.simplelists.com/sccpartners
 
Start a new conversation (thread): 
sccpartners@stoneandtilepros.simplelists.com
 
 
Visit list archives, subscribe, unsubscribe or change your subscription 
preferences:
http://stoneandtilepros.simplelists.com/sccpartners
 
Start a new conversation (thread): 
sccpartners@stoneandtilepros.simplelists.com
 
 
Visit list archives, subscribe, unsubscribe or change your subscription 
preferences:
http://stoneandtilepros.simplelists.com/sccpartners
 
Start a new conversation (thread): 
sccpartners@stoneandtilepros.simplelists.com
 

Visit list archives, subscribe, unsubscribe or change your subscription

preferences:

http://stoneandtilepros.simplelists.com/sccpartners

Start a new conversation (thread):

sccpartners@stoneandtilepros.simplelists.com

Visit list archives, subscribe, unsubscribe or change your subscription preferences: http://stoneandtilepros.simplelists.com/sccpartners Start a new conversation (thread): sccpartners@stoneandtilepros.simplelists.com