If you go to VMC website and click on natural stone product , the product is listed in the fillers

John E Freitag

Director

The Stone & Tile School

Office 407-567-7652

Cell 407-615-0134

jfreitag@thestoneandtileschool.com

www.thestoneandtileschool.com

What brand is VCM ?

Thanks

Justin

Sent from my iPhone

On Jul 18, 2014, at 9:24 AM, Bstandish <bstandish@facspecs.com> wrote:

Thanks John. I just put an order in for the grout from VMC. 

B

 

________________________________________

From the desk of

Baird Standish

Managing Partner

Facility Specialists, LLC

15 West Highland Ave. Suite E

Philadelphia, PA 19118

Phone: 215-732-7505

Fax: 215-546-9160

www.facspecs.com

On Jul 18, 2014, at 12:04 PM, "John Freitag" <jfreitag@thestoneandtileschool.com> wrote:

Baird,

 

I have used the 2 part product and do not care for it. If the instructions are state 2 part liquid and 7 parts of powder,then secure a measuring cup and fill the cup with 7 cups of powder and then add 2 cups of liquid.

I prefer to use the traver fill from VMC out of Dallas, TX  the product is a powder and you just add water. The pot life is short 5 to 7 minutes.

Hone the floor up to at least 220 using a grout float, float the filling in all holes. Depending upon the number of holes we often float over the entire floor  after the 220 hone.

Allow the fill to cure overnioght, then the next day come back and clean off with a natural hair pad and then polish. If you are going to hone to 400 then hone the floor with the 400 and then polish or do whatever finish you want.

This fill from VMC is an easy fill to use.

 

 

John E Freitag

Director

The Stone & Tile School

Office 407-567-7652

Cell 407-615-0134

jfreitag@thestoneandtileschool.com

 

<image001.jpg>

 

www.thestoneandtileschool.com

 

 

 

From: list-manager@stoneandtilepros.simplelists.com [mailto:list-manager@stoneandtilepros.simplelists.com] On Behalf Of Baird Standish
Sent: Friday, July 18, 2014 8:52 AM
To: sccpartners@stoneandtilepros.simplelists.com
Subject: Traverfiil method

 

Hello partners. We are working on the restoration of a travertine floor. I recently purchased a gallon kit of Bonstone Traverfill, which is a two part material involving both powder and liquid. I tried to find the recent thread where this was discussed, but for some reason I cannot find it.  The instructions are fairly vague.  They suggest either a mixture of 1 .5 liquid to 5 parts powder by weight, or 2 parts liquid to 7 parts powder by weight.  There has to be a better way to gauge the mixture. 

 

Also, they do not suggest a curing time. 

 

We have cut the floor to 100 grit and my plan is to test some of the areas. Am I on track if I fill after 100, cut the floor with 200 and then continue honing or polishing as necessary?  How long do I have to let this stuff dry?

Thanks

Baird

 

--

________________________________________
From the desk of
Baird Standish
Managing Partner
Facility Specialists, LLC
15 West Highland Ave.
Suite E
Philadelphia, PA 19118
Phone: 215-732-7505
Fax: 215-546-9160
www.facspecs.com

 

Visit list archives, subscribe, unsubscribe or change your subscription 

preferences:

http://stoneandtilepros.simplelists.com/sccpartners

Start a new conversation (thread): 

sccpartners@stoneandtilepros.simplelists.com

Visit list archives, subscribe, unsubscribe or change your subscription 

preferences:

http://stoneandtilepros.simplelists.com/sccpartners

Start a new conversation (thread): 

sccpartners@stoneandtilepros.simplelists.com

Visit list archives, subscribe, unsubscribe or change your subscription 

preferences:

http://stoneandtilepros.simplelists.com/sccpartners

Start a new conversation (thread): 

sccpartners@stoneandtilepros.simplelists.com

Visit list archives, subscribe, unsubscribe or change your subscription 

preferences:

http://stoneandtilepros.simplelists.com/sccpartners

Start a new conversation (thread): 

sccpartners@stoneandtilepros.simplelists.com

Visit list archives, subscribe, unsubscribe or change your subscription 

preferences:

http://stoneandtilepros.simplelists.com/sccpartners

Start a new conversation (thread): 

sccpartners@stoneandtilepros.simplelists.com