Thanks Stu! Sounds like a fun weekend! BTW, nobody drinks Fosters here in Australia. Ill PM you my address. Thanks again. Been needing something hotter for countertops.
From: list-manager@stoneandtilepros.simplelists.com [mailto:list-manager@stoneandtilepros.simplelists.com] On Behalf Of stuart rosen
Sent: Tuesday, 9 December 2014 7:59 AM
To: sccpartners@stoneandtilepros.simplelists.com
Subject: Re: countertops/vanities pricing
Mike
Give me your address I will send some MB12 for you to try.
Goes well with a couple of pieces of dull stone and a cold Fosters Lager
I think you will have some fun with it.
On Mon, Dec 8, 2014 at 4:44 PM, Mike Marsoun <nulifesc@bigpond.com> wrote:
Thanks stu. I'll get some mb12. I find that a 400 Genisis gets everything usually and easier to transition to resins. The only reason I hone so high is because of the 5x being more difficult to pop a shine at 800. Hard to find good products here and super expensive. My go-to is the Tenax 5x because it is easily available and cheap.
Sent from my iPhone
On 9 Dec 2014, at 2:14 am, stuart rosen <mail@stoneshine.com> wrote:I hate to see anyone lower their pricing but if you get $1200 for a sixty sq ft kitchen you could lower your rate some.
Seems like you do a lot of steps-just curious why do you skip the 220 grit?
You could use a faster process-start with a 220 genesis where there is etched or worn areas.
You could go right to 220 resin or in some cases 400 resin then go to 800 and polish with a dry polishing powder. Why waste all that time using 5x on a countertop if you don't have to. In most cases a product like MB12 will give you great results quickly.
On Sat, Dec 6, 2014 at 2:02 AM, Mike Marsoun <nulifesc@bigpond.com> wrote:
What do you guys charge for countertops? I have been at $200m2 ($20sf) for a long time, seems to work but I have a large commercial job I am bidding and was wondering how low I could go. Usually I go 400 genisis (electroplated) dry, then 120r, 400r, 800r 1800r, then5x. I will stop ar 800r sometimes but I rather do a quick pass with the diamonds than have to go hard with the powder.
Visit list archives, subscribe, unsubscribe or change your subscriptionpreferences:http://stoneandtilepros.simplelists.com/sccpartnersStart a new conversation (thread):sccpartners@stoneandtilepros.simplelists.com
--Regards,
Stu Rosen
201-446-1200"EVERYTHING MATTERS"
Visit list archives, subscribe, unsubscribe or change your subscriptionpreferences:http://stoneandtilepros.simplelists.com/sccpartnersStart a new conversation (thread):sccpartners@stoneandtilepros.simplelists.comVisit list archives, subscribe, unsubscribe or change your subscriptionpreferences:http://stoneandtilepros.simplelists.com/sccpartnersStart a new conversation (thread):sccpartners@stoneandtilepros.simplelists.com
--Regards,
Stu Rosen
201-446-1200"EVERYTHING MATTERS"
Visit list archives, subscribe, unsubscribe or change your subscriptionpreferences:http://stoneandtilepros.simplelists.com/sccpartnersStart a new conversation (thread):sccpartners@stoneandtilepros.simplelists.comVisit list archives, subscribe, unsubscribe or change your subscription preferences: http://stoneandtilepros.simplelists.com/sccpartners Start a new conversation (thread): sccpartners@stoneandtilepros.simplelists.com