Hi Stu:

Relating to your comment on cutting deeper than we're use to. To get a better result and no dust.

The pictures below of before and after show a older floor that required a deep cut like you where mentioning, the boss of the plant said, for the last 10 years they just kept rolling epoxy on it. We started our cut with (one bar 6 grit metal) and went to 800 resin. Also like your situation they can’t have any dust either so we used that powder in the slurry that make the slurry look like blown insulation and shoveled it into a dumpsters. This is the main walkway through the plant and was done a year ago. Its still looks this good as we speak. We where there last week to price out some more areas… That's how we know how its holding up. This hall is actually 330 feet long. We did the Husqvarna Hiperfloor system.

 http://www.husqvarna.com/files/husqvarna/construction/hiperfloor2013/Husqvarna_Hiperfloor_Commercial_Finish.pdf

 Of coarse starting at the lower grit..6 metal and we... re-densified again after 200 grit resin. On their maintenance they scrub a couple times a day with auto scrubbers and twice a week they put Prosoco's daily cleaner in the rinse water that has a touch of densifier in it.

 






On Jun 21, 2015, at 3:28 PM, stuart rosen <mail@stoneshine.com> wrote:

Yeah I think so-they wanted a coating-that's what we gave them because the surface is so trashed.
But I think we will try grinding deep and densifying to rejection, than bringing up to a smooth finish.
Its a dusting issue they are having. 

On Sun, Jun 21, 2015 at 3:23 PM, Randy Frye <rfrye@comcast.net> wrote:
Polished concrete, Is the only sure thing. 

On Jun 21, 2015, at 1:29 PM, stuart rosen <mail@stoneshine.com> wrote:

Does anyone know of a good concrete coating for a high traffic warehouse running forklifts.
we applied an epoxy coating and a year later it is wearing badly in some areas.

On Sat, Jun 20, 2015 at 7:44 PM, Randy Frye <rfrye@comcast.net> wrote:
Heres a start. He trains and does this work on a daily basis. 

Mark 712-253-1841

She is a good lead also for information
Lindy 254-498-6635

On Jun 20, 2015, at 1:04 PM, Baird Standish <bairdstandish@gmail.com> wrote:

Hi. Does anyone out there have a bead on obtaining polyaspartic coating supplies and training? Thanks so much. 
Baird 


Sent from Mailbox
 
Visit list archives, subscribe, unsubscribe or change your subscription 
preferences:
http://stoneandtilepros.simplelists.com/sccpartners
 
Start a new conversation (thread): 
sccpartners@stoneandtilepros.simplelists.com


 
Visit list archives, subscribe, unsubscribe or change your subscription 
preferences:
http://stoneandtilepros.simplelists.com/sccpartners
 
Start a new conversation (thread): 
sccpartners@stoneandtilepros.simplelists.com




--
Regards,
Stu Rosen
201-446-1200

"EVERYTHING MATTERS"


 
Visit list archives, subscribe, unsubscribe or change your subscription 
preferences:
http://stoneandtilepros.simplelists.com/sccpartners
 
Start a new conversation (thread): 
sccpartners@stoneandtilepros.simplelists.com


 
Visit list archives, subscribe, unsubscribe or change your subscription 
preferences:
http://stoneandtilepros.simplelists.com/sccpartners
 
Start a new conversation (thread): 
sccpartners@stoneandtilepros.simplelists.com




--
Regards,
Stu Rosen
201-446-1200

"EVERYTHING MATTERS"


 
Visit list archives, subscribe, unsubscribe or change your subscription 
preferences:
http://stoneandtilepros.simplelists.com/sccpartners
 
Start a new conversation (thread): 
sccpartners@stoneandtilepros.simplelists.com