This email was sent from yahoo.com which does not allow forwarding of emails via email lists. Therefore the sender's email address (billselik@yahoo.com) has been replaced with a dummy one.

This is best repaired by someone that can router out the bottom side and inset some support.  I would recommend a fabricator unless you are able to do this yourself.  Small table are not a problem but that much weight will probably snap again when you move it.

Good luck, Bill Selik

Gourmet Stone Care

On Tuesday, December 1, 2015 6:44 PM, Baird Standish <bairdstandish@gmail.com> wrote:

It is not attached to the surface. Some pieces have broken off completely on the edge. In other places there are hairline cracks that I can see run straight through and the pieces will fall apart or at least will if nudged. They are in a well. The broken pieces are to the outside and mostly in two opposite corners - one corner is hairlined in different places and in the other the piece fell out b

________________________________________

From the desk of

Baird Standish

Managing Partner

Facility Specialists, LLC

15 West Highland Ave. Suite E

Philadelphia, PA 19118

Phone: 215-732-7505

Fax: 215-546-9160

http://www.facspecs.com/

On Dec 1, 2015, at 8:23 PM, stuart rosen <mail@stoneshine.com> wrote:

Is it attached to the surface you are trying to lift it off of?

Do the cracked pieces come out-hard to see the pic-is it in a well.

Are the broken pieces on the outside or random.

Does it have to come off-

On Tue, Dec 1, 2015 at 6:53 PM, Baird Standish <bairdstandish@gmail.com> wrote:

Hi gang. Here is an interesting problem. I have a large 6x4 or so travertine table that was dropped by some movers and some areas were cracked all the way through. Repairing it is probably not a big deal-the pieces will probably glue back pretty easily. But the problem is lifting the table out of the table (it is about 300 lbs) without it all falling apart. I am thinking about getting suction cups and lifting it so that the whole thing is balanced over the edge, with a blanket in place to protect the wood, and then gluing and clamping the pieces back. The underside of the tabletop is covered so I can't push it up from below. I tried lifting with my fingers but it's not moving. Wondered if anyone has any other ideas.
Thanks.
B

Visit list archives, subscribe, unsubscribe or change your subscription
preferences:
http://stoneandtilepros.simplelists.com/sccpartners

Start a new conversation (thread):
sccpartners@stoneandtilepros.simplelists.com




________________________________________
From the desk of
Baird Standish
Managing Partner
Facility Specialists, LLC
15 West Highland Ave. Suite E
Philadelphia, PA 19118
Phone: 215-732-7505
Fax: 215-546-9160
http://www.facspecs.com/

--

Regards,
Stu Rosen
201-446-1200

http://www.mbstonecare.com/

http://www.stoneshine.com/

http://www.mbstonepro.com/

"EVERYTHING MATTERS"

 
Visit list archives, subscribe, unsubscribe or change your subscription 
preferences:
http://stoneandtilepros.simplelists.com/sccpartners
 
Start a new conversation (thread): 
sccpartners@stoneandtilepros.simplelists.com

 
Visit list archives, subscribe, unsubscribe or change your subscription 
preferences:
http://stoneandtilepros.simplelists.com/sccpartners
 
Start a new conversation (thread): 
sccpartners@stoneandtilepros.simplelists.com

 
Visit list archives, subscribe, unsubscribe or change your subscription 
preferences:
http://stoneandtilepros.simplelists.com/sccpartners
 
Start a new conversation (thread): 
sccpartners@stoneandtilepros.simplelists.com