I will. On the website right now again. Also looking at the Klindex pad driver. Would that driver work with the metal and copper pads?
From: list-manager@stoneandtilepros.simplelists.com [mailto:list-manager@stoneandtilepros.simplelists.com] On Behalf Of stuart rosen
Sent: Monday, September 26, 2016 3:34 PM
To: sccpartners@stoneandtilepros.simplelists.com
Subject: Re: Marble floor lippage
We have stone soap-it comes in 5 litre containers for $199.00 each
Its expensive but a great product.
We have it in quart bottles($64.95) under the Shimmer label on our website.
Look at specialty cleaners or sealers and enhancers or just search for stone soap or shimmer.
We use it a lot for honed floors.
On Mon, Sep 26, 2016 at 1:22 PM, Richard Middleton <richard@prosteem.com> wrote:
Stu, where do you buy Klindex stone soap at?
From: list-manager@stoneandtilepros.simplelists.com [mailto:list-manager@stoneandtilepros.simplelists.com] On Behalf Of stuart rosen
Sent: Monday, September 26, 2016 1:56 PM
Yes they are velcro backed-if your drive plate has good velcro you should be fine.
Check out the floor and stone first-first grinding jobs have a habit of getting your attention!
Is there sanded grout? How wide are the joints ? The quality of the install and the type of stone.
On Mon, Sep 26, 2016 at 12:45 PM, Richard Middleton <richard@prosteem.com> wrote:
Im looking at your grinding kit now online. Can I use those on my 17” weighted Hawk machine and how do they set up?
From: list-manager@stoneandtilepros.simplelists.com [mailto:list-manager@stoneandtilepros.simplelists.com] On Behalf Of stuart rosen
Sent: Monday, September 26, 2016 1:44 PM
Great-I think it is important to become experienced at flattening floors. It isn't for everyone but if you get comfortable doing those types of jobs you can do well with them.
On Mon, Sep 26, 2016 at 10:44 AM, Richard Middleton <richard@prosteem.com> wrote:
I will be looking at the job tomorrow. Will take a few pics. I was thinking low end at 8.00 a foot. We get average of 4.00 for hone polish seal on most marble. Stu I will get in touch with you or your staff about metals I will need. Thanks everyone for feedback.
Have a Blessed Day!
Richard Middleton
From: list-manager@stoneandtilepros.simplelists.com [mailto:list-manager@stoneandtilepros.simplelists.com] On Behalf Of stuart rosen
Sent: Sunday, September 25, 2016 7:37 PM
To: sccpartners@stoneandtilepros.simplelists.com
Subject: Re: Marble floor lippage
We grind a good number of Surfaces . For marble, pricing can go up to $10.00 a sq ft but really depends on the job.
I agree with Randy -see what the competition is doing. I also agree with Greg-get experience-research your area-see where you need to be-charge accordingly.
I agree with Randy on using same diamonds as long as they are quality.
It makes a big difference-The first cut of any grinding job is the most important cut-never rush that one.
On Sun, Sep 25, 2016 at 6:41 AM, Randy Frye <rfrye6@gmail.com> wrote:
Make sure your metals are from the same manufacture. I just did a job and first cut was 30 metal by super abrasives. Then went to a 50 metal from another company and proceeded up to 100 resin at that point I noticed the 30’s where still slightly visible. Went back to those same 50 metals and went over again very thorough and still no luck. I went ahead and got the super abrasive 50 metals out even though they where almost used up, and tried them and wipe the 30’s out easily. A lesson learned for me.
--
Regards,
Stu Rosen
201-446-1200
Visit list archives, subscribe, unsubscribe or change your subscription
preferences:
http://stoneandtilepros.simplelists.com/sccpartners
Start a new conversation (thread):
sccpartners@stoneandtilepros.simplelists.com
--
Regards,
Stu Rosen
201-446-1200
Visit list archives, subscribe, unsubscribe or change your subscription
preferences:
http://stoneandtilepros.simplelists.com/sccpartners
Start a new conversation (thread):
sccpartners@stoneandtilepros.simplelists.com
--
Regards,
Stu Rosen
201-446-1200
Visit list archives, subscribe, unsubscribe or change your subscription
preferences:
http://stoneandtilepros.simplelists.com/sccpartners
Start a new conversation (thread):
sccpartners@stoneandtilepros.simplelists.com
--
Regards,
Stu Rosen
201-446-1200
Visit list archives, subscribe, unsubscribe or change your subscription
preferences:
http://stoneandtilepros.simplelists.com/sccpartners
Start a new conversation (thread):
sccpartners@stoneandtilepros.simplelists.com