I just looked at this picture of the 12 year old floor. You must clean all grout lines before you float with grout. Color won't match or may not stick. You are probably going to have some issues with the mud veins opening up when grinding so you may need
to add some money for filling them.
This is the marble floor with lippage. Home owner had installed twelve years ago with nothing done to it since. They are doing a renovation on the home between now and end of year. Looks like total of 950 square feet. Worst lippage in dining room at 1/8 inch and other places at 1/16 inch. Home will be vacant at time of floor restoration.
Thanks Everyone!
Richard
From: list-manager@stoneandtilepros.simplelists.com [mailto:list-manager@stoneandtilepros.simplelists.com]
On Behalf Of stuart rosen
Sent: Monday, September 26, 2016 6:18 PM
To: sccpartners@stoneandtilepros.simplelists.com
Subject: Re: Marble floor lippage
Yes we run 4 diamonds on our machines(they are easy to place 12-3-6-9 o'clock position-but everyone has their own preference from 3 to 6 pieces.
I like Pats idea about grinding a sample floor prior to the first grinding job.
On Mon, Sep 26, 2016 at 3:37 PM, Pat Staples <cpstaples@msn.com> wrote:
If you have not done lippage removal before. Get a couple boxes of tiles and put them down and try it so you have some practice before you go into a customer's house. I have seen several companies go in and ruined floors because they have no experience with it
Sent from my Sprint Samsung Galaxy S7.
-------- Original message --------
From: stuart rosen <mail@stoneshine.com>
Date: 9/26/16 2:43 PM (GMT-05:00)
Subject: Re: Marble floor lippage
Great-I think it is important to become experienced at flattening floors. It isn't for everyone but if you get comfortable doing those types of jobs you can do well with them.
On Mon, Sep 26, 2016 at 10:44 AM, Richard Middleton <richard@prosteem.com> wrote:
I will be looking at the job tomorrow. Will take a few pics. I was thinking low end at 8.00 a foot. We get average of 4.00 for hone polish seal on most marble. Stu I will get in touch with you or your staff about metals I will need. Thanks everyone for feedback.
Have a Blessed Day!
Richard Middleton
From: list-manager@stoneandtilepros.simplelists.com [mailto:list-manager@stoneandtilepros.simplelists.com] On Behalf Of stuart rosen
Sent: Sunday, September 25, 2016 7:37 PM
To: sccpartners@stoneandtilepros.simplelists.com
Subject: Re: Marble floor lippage
We grind a good number of Surfaces . For marble, pricing can go up to $10.00 a sq ft but really depends on the job.
I agree with Randy -see what the competition is doing. I also agree with Greg-get experience-research your area-see where you need to be-charge accordingly.
I agree with Randy on using same diamonds as long as they are quality.
It makes a big difference-The first cut of any grinding job is the most important cut-never rush that one.
On Sun, Sep 25, 2016 at 6:41 AM, Randy Frye <rfrye6@gmail.com> wrote:
Make sure your metals are from the same manufacture. I just did a job and first cut was 30 metal by super abrasives. Then went to a 50 metal from another company and proceeded up to 100 resin at that point I noticed the 30’s where still slightly visible. Went back to those same 50 metals and went over again very thorough and still no luck. I went ahead and got the super abrasive 50 metals out even though they where almost used up, and tried them and wipe the 30’s out easily. A lesson learned for me.
On Sep 25, 2016, at 4:27 AM, Roger Konarski (via sccpartners list) <nobody@simplelists.com> wrote:
This email was sent from yahoo.com which does not allow forwarding of emails via email lists. Therefore the sender's email address (qm144@yahoo.com) has been replaced with a dummy one.
My techs like the metals and coppers from Stu for cutting floors. Knocks down lippage with out leaving deep scratch patterns. Use his metals , followed by coppers then onto 120 resins.
Roger
On Saturday, September 24, 2016 12:02 PM, Richard Middleton <richard@prosteem.com> wrote:
Partners, I will be bidding a residential job for lippage on marble floor. Any suggestions on procedures would be helpful. Machines we have are Hawk 17” and 20”. Also pricing ideas would be helpful. Thank you for any input. Have a great weekend.
Best Regards,
Richard Middleton
Visit list archives, subscribe, unsubscribe or change your subscriptionpreferences:http://stoneandtilepros.simplelists.com/sccpartnersStart a new conversation (thread):sccpartners@stoneandtilepros.simplelists.com
Visit list archives, subscribe, unsubscribe or change your subscriptionpreferences:http://stoneandtilepros.simplelists.com/sccpartnersStart a new conversation (thread):sccpartners@stoneandtilepros.simplelists.com
Visit list archives, subscribe, unsubscribe or change your subscriptionpreferences:http://stoneandtilepros.simplelists.com/sccpartnersStart a new conversation (thread):sccpartners@stoneandtilepros.simplelists.com
--
Regards,
Stu Rosen
201-446-1200
"EVERYTHING MATTERS"
Visit list archives, subscribe, unsubscribe or change your subscriptionpreferences:http://stoneandtilepros.simplelists.com/sccpartnersStart a new conversation (thread):sccpartners@stoneandtilepros.simplelists.comVisit list archives, subscribe, unsubscribe or change your subscriptionpreferences:http://stoneandtilepros.simplelists.com/sccpartnersStart a new conversation (thread):sccpartners@stoneandtilepros.simplelists.com
--
Regards,
Stu Rosen
201-446-1200
"EVERYTHING MATTERS"
Visit list archives, subscribe, unsubscribe or change your subscriptionpreferences:http://stoneandtilepros.simplelists.com/sccpartnersStart a new conversation (thread):sccpartners@stoneandtilepros.simplelists.comVisit list archives, subscribe, unsubscribe or change your subscriptionpreferences:http://stoneandtilepros.simplelists.com/sccpartnersStart a new conversation (thread):sccpartners@stoneandtilepros.simplelists.com
--
Regards,
Stu Rosen
201-446-1200
"EVERYTHING MATTERS"
Visit list archives, subscribe, unsubscribe or change your subscription
preferences:
http://stoneandtilepros.simplelists.com/sccpartners
Start a new conversation (thread):
sccpartners@stoneandtilepros.simplelists.com
Visit list archives, subscribe, unsubscribe or change your subscription preferences: http://stoneandtilepros.simplelists.com/sccpartners Start a new conversation (thread): sccpartners@stoneandtilepros.simplelists.com