Just discussed this again with the installer. It appears that the staining is occurring on the cut edges of the tile. Which leads me to think that it’s more porous there and it’s pulling in the water. Someone in this thread had mentioned an epoxy additive that could be applied to the edges of the tile that is not covered with grout. This sounds like a solution.

Sent from my iPhone

On Mar 8, 2018, at 11:17 AM, Bob Murrell <bmurrell@m3techinc.com> wrote:

I agree with Fred and Hector. There is probably and integrity (weep holes, setting material, grout and/or the stone) failure somewhere.

Sent from Bob Murrell's iPhone
M3 Technologies, Inc.
865-607-0957
Office 800-342-4533
www.go2m3.com


On Mar 8, 2018, at 11:14 AM, Fred Hueston <fhueston@gmail.com> wrote:

Also keep in mind that steam is a vapor and most impregnators are vapor permeable.

Virus-free. www.avast.com

On Thu, Mar 8, 2018 at 11:09 AM, <csantospago@gmail.com> wrote:
Interesting Hector. All I know is this material is like a wick on any unpolished surfaces so it’s possible the little edge above the grout line is pulling in water. Especially since it’s a steam shower.
They use the same dolomite material on some vanities in a condo complex in Boston. The union guys broke a few of them and I had to go replace them. I used 100 % silicone to secure them to the cabinet and the areas where the silicone was stayed dark for three weeks.
Trying to give them an option other than removing the tile.
Thank you, Chris

Sent from my iPhone

> On Mar 8, 2018, at 9:43 AM, hector castillo <hectorcastillo@comcast.net> wrote:
>
> I have seen pin holes in this type of grout.
> This lets water in. I had to heat removal a floor 2 years ago in a shower floor what a pain in the butt.
> We installed  non sanded grout. For the tight grout joint this fixed the problem. I don’t know if this fix will fix the problem.
> Hector Castillo
>
> -----Original Message-----
> From: sccpartners@stoneandtilepros.simplelists.com [mailto:sccpartners@stoneandtilepros.simplelists.com] On Behalf Of csantospago@gmail.com
> Sent: Thursday, March 8, 2018 6:34 AM
> To: sccpartners@stoneandtilepros.simplelists.com
> Subject: Re: Dolomite tile shower with epoxy grout
>
> The grout was Laticrete spectra-lock epoxy grout bright white.  I did not do the installation but I know that’s what they used
>
> Sent from my iPhone
>
>> On Mar 8, 2018, at 9:29 AM, hector castillo <hectorcastillo@comcast.net> wrote:
>>
>> Please show a photo of  the grout that was used.
>> Hector Castillo
>>
>> -----Original Message-----
>> From: sccpartners@stoneandtilepros.simplelists.com
>> [mailto:sccpartners@stoneandtilepros.simplelists.com] On Behalf Of
>> csantospago@gmail.com
>> Sent: Thursday, March 8, 2018 5:59 AM
>> To: Sccpartners Email Support
>> <sccpartners@stoneandtilepros.simplelists.com>
>> Subject: Dolomite tile shower with epoxy grout
>>
>> Partners,
>>
>> Got called to this job about a month ago to resolve the staining issue
>> in this steam shower. I tried using a poultice with TSP and another
>> section I used 40 volume peroxide cream.
>> Both products worked but the peroxide cream was much quicker and
>> easier to use. Also the poultice left the area stained for more than a
>> week while the cream dried up within a day.
>> Over a few weeks we did about 3 to 4 Applications removing all the
>> staining and then we sealed everything with an impregnating sealer from M3.
>> I just got a text from the homeowner and the staining has reappeared.
>> I know that dolomite is a very sensitive material and probably should
>> not be used in a shower setting. Not sure if the epoxy grout is the problem.
>> Any thoughts from anybody?
>> Thank you,
>> Chris Santospago
>> Restoration by design stone
>>
>>
>> Visit list archives, subscribe, unsubscribe or change your
>> subscription
>> preferences:
>> http://stoneandtilepros.simplelists.com/sccpartners
>>
>> Start a new conversation (thread):
>> sccpartners@stoneandtilepros.simplelists.com
>>
>>
>>
>> Visit list archives, subscribe, unsubscribe or change your
>> subscription
>> preferences:
>> http://stoneandtilepros.simplelists.com/sccpartners
>>
>> Start a new conversation (thread):
>> sccpartners@stoneandtilepros.simplelists.com
>>
>
> Visit list archives, subscribe, unsubscribe or change your subscription
> preferences:
> http://stoneandtilepros.simplelists.com/sccpartners
>
> Start a new conversation (thread):
> sccpartners@stoneandtilepros.simplelists.com
>
>
>
> Visit list archives, subscribe, unsubscribe or change your subscription
> preferences:
> http://stoneandtilepros.simplelists.com/sccpartners
>
> Start a new conversation (thread):
> sccpartners@stoneandtilepros.simplelists.com
>

Visit list archives, subscribe, unsubscribe or change your subscription
preferences:
http://stoneandtilepros.simplelists.com/sccpartners

Start a new conversation (thread):
sccpartners@stoneandtilepros.simplelists.com




--
Frederick M. Hueston
www.stoneforensics.com
office             321 514 6845      
Stone Inspection and Troubleshooting seminar June 11-14, Melbounre FL
For more details see the training section at www.stoneforensics.com
check out the Stone and Tile Radio Show at http://www.blogtalkradio.com/drfred  New show starts February 21 at 6pm EST




 
Visit list archives, subscribe, unsubscribe or change your subscription 
preferences:
http://stoneandtilepros.simplelists.com/sccpartners
 
Start a new conversation (thread): 
sccpartners@stoneandtilepros.simplelists.com

 
Visit list archives, subscribe, unsubscribe or change your subscription 
preferences:
http://stoneandtilepros.simplelists.com/sccpartners
 
Start a new conversation (thread): 
sccpartners@stoneandtilepros.simplelists.com