Yeah -well noted-I bet he would pay you around $25/2750 to do it.
Run the UFO with the electroplated then the blend in the edges-

On Fri, Aug 3, 2018 at 4:56 PM, <csantospago@gmail.com> wrote:
It’s probably about 50 ft.² max. This is a fabricator so he’s not going to want to spend that kind of money. Already told him it’s a bitch of a job so he should probably do it himself. He sends me a lot of work and he expects favors in return but I’m not busting my butt on this countertop especially with the edges. 
Thanks Stu and Fred. Appreciate the feedback

Sent from my iPhone

On Aug 3, 2018, at 4:51 PM, Stuart Rosen <mail@stoneshine.com> wrote:

Chris-you should be ok with the edges-you can use sandpaper and different type of abrasives-That's a $3500.00 job-how many linear feet is the kitchen.

On Fri, Aug 3, 2018 at 3:45 PM, Fred Hueston <fhueston@gmail.com> wrote:
Hydrofluoric acid will work but it is very dangerous to use. I would walk away before using that acid

On Fri, Aug 3, 2018 at 3:42 PM, <csantospago@gmail.com> wrote:
Hi Stu. Yes it is fantasy brown but the problem I have is it’s already installed with extremely expensive wall tile on top of it. Going to be tough to get up to the edges on the sides and backsplash.
Was hoping some type of acid honing

Sent from my iPhone

On Aug 3, 2018, at 3:35 PM, Stuart Rosen <mail@stoneshine.com> wrote:

Fantasy Brown-its gets sold as Quartzite,Marble and or Granite.

It will be straight forward to hone just tedious.
Possible to use 70 then 120 grit electroplated pads then transition to a copper pad like a 120 or 220 then finish with honing powders.
It is classified as a marble-looks better honed-

On Fri, Aug 3, 2018 at 2:48 PM, <csantospago@gmail.com> wrote:
My fabricator client installed this granite countertop and the homeowner decided they wanted honed instead.
Backsplash tile has already been installed.
Mechanically honing this is probably impossible at this point. I tried putting some acid on these samples and was able to get a very little reaction. Apparently there is some calcium in this material. The fabricator sells it as a marble.
Has anybody had experience with some type of chemical to get a nice even hone?

Thank you,
Chris Santospago
Restoration by Design Stone

Visit list archives, subscribe, unsubscribe or change your subscription
preferences:
http://stoneandtilepros.simplelists.com/sccpartners

Start a new conversation (thread):
sccpartners@stoneandtilepros.simplelists.com




Sent from my iPhone



--


Visit list archives, subscribe, unsubscribe or change your subscription
preferences:
http://stoneandtilepros.simplelists.com/sccpartners

Start a new conversation (thread):
sccpartners@stoneandtilepros.simplelists.com


Visit list archives, subscribe, unsubscribe or change your subscription
preferences:
http://stoneandtilepros.simplelists.com/sccpartners

Start a new conversation (thread):
sccpartners@stoneandtilepros.simplelists.com




--
Frederick M. Hueston
www.stoneforensics.com
office             321 514 6845      
Stone Inspection and Troubleshooting seminar June 11-14, Melbounre FL
For more details see the training section at www.stoneforensics.com
check out the Stone and Tile Radio Show at http://www.blogtalkradio.com/drfred  Airs every Wednesday at 6pm EST





Visit list archives, subscribe, unsubscribe or change your subscription
preferences:
http://stoneandtilepros.simplelists.com/sccpartners

Start a new conversation (thread):
sccpartners@stoneandtilepros.simplelists.com




--


Visit list archives, subscribe, unsubscribe or change your subscription
preferences:
http://stoneandtilepros.simplelists.com/sccpartners

Start a new conversation (thread):
sccpartners@stoneandtilepros.simplelists.com


Visit list archives, subscribe, unsubscribe or change your subscription
preferences:
http://stoneandtilepros.simplelists.com/sccpartners

Start a new conversation (thread):
sccpartners@stoneandtilepros.simplelists.com




--
Regards,
Stu Rosen
201-446-1200