RE: [sccpartners] Granite Floor !!!! Roger Konarski 21 Jun 2010 00:41 EDT
John, Thanks for the info. Some more info on the job. The floor is checkerboard white thassos and black absolute. Yes they only want a honed finish. So I assume your recommendation for handling the job is the same strategy. Normally when it comes to honed granite, you want to use a color enhancer as a sealer. To me that present a problem because you only want to enhance the granite. Thus I would envision taping off the white thassos and color enhancing the granite. Then removing the tape and sealing the entire floor. Any suggestions or feedback would be appreciated. Thanks, RK --- On Fri, 6/18/10, John Freitag <jfreitag@thestoneandtileschool.com> wrote: > From: John Freitag <jfreitag@thestoneandtileschool.com> > Subject: RE: [sccpartners] Granite Floor !!!! > To: "Restoration and Maintenance" <sccpartners@stoneandtilepros.com> > Date: Friday, June 18, 2010, 8:15 AM > Roger, > > The mastercraft machine will work fine, you may add some > weight to the first > grind if you're going to flatten the floor. Does the > customer want the floor > flat or just honed? There is a difference. If they only > want the floor to be > at a honed finish then you do not need to flatten it. Hone > the floor with a > 400 grit granite diamond, I use the 3 inch Ceramic pads > from StoneCare > Central. They are the DI-CP pads call Margie and she know > the pads. > > Then I would mount the diamonds on a hog hair pad, you can > buy a industrial > Velcro from StoneCare Central it comes 4 inches wide and 36 > inch long. Cut > this into 3 to 4 inch squares and glue them onto anew hog > hair pad. I like > placing 5 diamonds to a 17 inch pad. When attaching the > Velcro to the pad > use some super glue, the Velcro has a self adhesive on it > the glue just make > it stick better. Let the pad set over night with some > weight on it > > Your ready to grind if the final result is to achieve a > honed finish I would > try starting with a 400 grit granite diamond, NO your > marble diamonds will > not work! I would not use any weight on the machine for > this process. Once > the honing is complete if you have any picture framing use > a honing powder. > This will remove the picture framing and leave the floor at > a nice honed > finish. To remove the picture framing you may need to use a > 250 honing > powder then follow up with a 400 powder. Then seal the > floor > > If you have any other questions, please let me know > > > > John E. Freitag > President/Director > The Stone and Tile School > Office 407-567-7652 > Cell 407-615-0134 > jfreitag@thestoneandtileschool.com > > > > www.thestoneandtileschool.com > > > > -----Original Message----- > From: Roger Konarski [mailto:qm144@yahoo.com] > Sent: Thursday, June 17, 2010 8:10 PM > To: Restoration and Maintenance > Subject: [sccpartners] Granite Floor !!!! > > I got a call today on new granite floor insulation; I > believe they said it > was polished black absolute. They want a hone finished on > the floor. The > positives are that the floor trim has not been installed. > While I can top > polish granite with no problem, I have never ground flat a > granite floor. I > was told it is about 300 sq. ft. I have Mastercraft (that > needs to be > replaced). I also have a Clarke MP1800, would one of these > machines do the > job and what type of grinding disc and pads would you > possible recommend? > Thanks, > Roger > > > > -- > Powered by http://DiscussThis.com > Visit list archives, subscribe, unsubscribe or change your > subscription > preferences: > http://www.discussthis.com/members/sccpartners@stoneandtilepros.com > Start a new conversation (thread): sccpartners@stoneandtilepros.com > > > > > -- > Powered by http://DiscussThis.com > Visit list archives, subscribe, unsubscribe or change your > subscription preferences: > http://www.discussthis.com/members/sccpartners@stoneandtilepros.com > Start a new conversation (thread): sccpartners@stoneandtilepros.com > > > >