Stu,

What about wiping down with acid and then using the black dot to blend and
erase and etching or lines from the acid?

Ron
On Tue, January 17, 2017 8:02 am, stuart rosen wrote:
> Ron-I think the orbitals will take much longer than if you just spin
> makita's. Depending on the stone you can use a 7 inch black dot vortex pad
> by itself(its pretty aggressive) or use a resin diamond or electroplated
> to break the polish.
>
>
> On Tue, Jan 17, 2017 at 8:52 AM, Ron Moore <rmoore@americanstonecare.com>
>  wrote:
>
>
>> Thanks Pat, I have a couple orbital sanders that hook to a vac system,
>> I
>> was wondering if the spinergy (diamond impregnated pads) would be
>> aggressive enough to blend out scratch pattern etc... On Mon, January
>> 16, 2017 7:16 pm, Pat Staples wrote:
>>
>>> Now that you have figured out you can get a lift in there. I just did
>>> a job like this where they wanted to shine taken off and a honed
>>> finish. We used 120 Grit resin diamonds on 7-inch backing plates then
>>> went over everything with a 100 Grit diamond impregnated pad that we
>>> got from M3 Technologies the diamond impregnated pad removed the resin
>>> smears left by the resin diamond. I have never used dry diamonds but I
>>> guess they may work. We used water feed machines and just kept a guy
>>> on the ground with a vacuum. Very simple job to do but your arms will
>>> get a little tired from holding up the hand machine for hours on end
>>>
>>>
>>>
>>> Sent from my Sprint Samsung Galaxy S7.
>>>
>>>
>>>
>>>
>>> -------- Original message --------
>>> From: Pat Staples <cpstaples@msn.com>
>>> Date: 1/16/17 6:07 PM (GMT-05:00)
>>> To: sccpartners@stoneandtilepros.simplelists.com
>>> Subject: RE: honing advice
>>>
>>>
>>>
>>> Then use one of the high reach scissor/platform  lifts, that will
>>> work well for you
>>>
>>>
>>>
>>> Sent from my Sprint Samsung Galaxy S7.
>>>
>>>
>>>
>>>
>>> -------- Original message --------
>>> From: Ron Moore <rmoore@americanstonecare.com>
>>> Date: 1/16/17 4:53 PM (GMT-05:00)
>>> To: sccpartners@stoneandtilepros.simplelists.com
>>> Subject: RE: honing advice
>>>
>>>
>>>
>>> Partners,
>>>
>>>
>>>
>>> The lobby floor is still cement, this is early in the construction
>>> stage. The is nothing under that we need to worry about.
>>>
>>>
>>>
>>> Ron
>>> On Mon, January 16, 2017 3:30 pm, Pat Staples wrote:
>>>
>>>
>>>> Depending upon the floor in the building we can only use a single
>>>> man lift. The bigger ones are usually too heavy to roll across the
>>>> lobby floor
>>>>
>>>>
>>>>
>>>> Sent from my Sprint Samsung Galaxy S7.
>>>>
>>>>
>>>>
>>>>
>>>>
>>>> -------- Original message --------
>>>> From: Ron Moore <rmoore@americanstonecare.com>
>>>> Date: 1/16/17 4:23 PM (GMT-05:00)
>>>> To: sccpartners@stoneandtilepros.simplelists.com
>>>> Subject: honing advice
>>>>
>>>>
>>>>
>>>>
>>>> Partners,
>>>>
>>>>
>>>>
>>>>
>>>> We have been asked to hone approx 2,000 sf of marble, vertical,
>>>> with a wall height of 35'. We can get a lift in, which is helpful. I
>>>> would love to hear your suggestions regarding this challenge. Thanks
>>>> in advance for your advice!
>>>>
>>>>
>>>> Ron Moore, President
>>>> American Stone Care, Inc.
>>>> 16458 Lone Oak Place
>>>> Hamilton, VA. 20158
>>>> 540-338-5559 o
>>>> 301-602-2307 c
>>>> www.americanstonecare.com<http://www.americanstonecare.com<h
>>>>
>> ttp://www.am
>>
>>>> ericanstonecare.com<http://www.americanstonecare.com>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>> Visit list archives, subscribe, unsubscribe or change your
>>>> subscription preferences:
>>>> http://stoneandtilepros.simplelists.com/sccpartners
>>>>
>>>>
>>>>
>>>>
>>>> Start a new conversation (thread):
>>>> sccpartners@stoneandtilepros.simplelists.com
>>>>
>>>>
>>>> Visit list archives, subscribe, unsubscribe or change your
>>>> subscription preferences:
>>>> http://stoneandtilepros.simplelists.com/sccpartners
>>>>
>>>>
>>>>
>>>>
>>>> Start a new conversation (thread):
>>>> sccpartners@stoneandtilepros.simplelists.com
>>>>
>>>>
>>>
>>>
>>> Ron Moore, President
>>> American Stone Care, Inc.
>>> 16458 Lone Oak Place
>>> Hamilton, VA. 20158
>>> 540-338-5559 o
>>> 301-602-2307 c
>>> www.americanstonecare.com<http://www.americanstonecare.com>
>>>
>>>
>>>
>>>
>>> Visit list archives, subscribe, unsubscribe or change your
>>> subscription preferences:
>>> http://stoneandtilepros.simplelists.com/sccpartners
>>>
>>>
>>>
>>> Start a new conversation (thread):
>>> sccpartners@stoneandtilepros.simplelists.com
>>>
>>>
>>>
>>> Visit list archives, subscribe, unsubscribe or change your
>>> subscription preferences:
>>> http://stoneandtilepros.simplelists.com/sccpartners
>>>
>>>
>>>
>>> Start a new conversation (thread):
>>> sccpartners@stoneandtilepros.simplelists.com
>>>
>>>
>>>
>>> Visit list archives, subscribe, unsubscribe or change your
>>> subscription preferences:
>>> http://stoneandtilepros.simplelists.com/sccpartners
>>>
>>>
>>>
>>> Start a new conversation (thread):
>>> sccpartners@stoneandtilepros.simplelists.com
>>>
>>>
>>
>>
>> Ron Moore, President
>> American Stone Care, Inc.
>> 16458 Lone Oak Place
>> Hamilton, VA. 20158
>> 540-338-5559 o
>> 301-602-2307 c
>> www.americanstonecare.com
>>
>>
>> Visit list archives, subscribe, unsubscribe or change your subscription
>>  preferences:
>> http://stoneandtilepros.simplelists.com/sccpartners
>>
>>
>> Start a new conversation (thread):
>> sccpartners@stoneandtilepros.simplelists.com
>>
>>
>
>
> --
> Regards,
> Stu Rosen
> 201-446-1200
> www.mbstonecare.com www.stoneshine.com www.mbstonepro.com
>
> "*EVERYTHING MATTERS"*
>
>
> Visit list archives, subscribe, unsubscribe or change your subscription
> preferences:
> http://stoneandtilepros.simplelists.com/sccpartners
>
>
> Start a new conversation (thread):
> sccpartners@stoneandtilepros.simplelists.com
>
>

Ron Moore, President
American Stone Care, Inc.
16458 Lone Oak Place
Hamilton, VA. 20158
540-338-5559 o
301-602-2307 c
www.americanstonecare.com